Double Pocket Door Installation Guide: Step-by-Step Instructions

SartoDoors interior doors are engineered for controlled indoor environments. They are not rated for exterior use, garages, laundry rooms with open steam, or any space where humidity regularly exceeds 70%. Installing interior doors in high-moisture zones voids the warranty and causes delamination, swelling, and finish failure regardless of finish type.

A consistent, gentle cleaning routine prevents the buildup of grime that forces you into harsher cleaning later. This simple process takes under two minutes and should be done weekly in high-traffic areas.

• Dust first: Use a dry microfiber cloth or a soft feather duster. Always wipe with the grain (vertical strokes on most doors). Dust settles into texture grooves — never skip this step before wet-wiping.
• Damp-wipe: Lightly dampen a clean microfiber cloth with plain lukewarm water. Wring it until almost dry — the cloth should feel barely moist, not wet. Wipe the surface in gentle passes.
• Dry immediately: Follow with a dry microfiber cloth. Never leave water sitting on any door surface. Even briefly standing water can cause micro-lifting of finish edges.
• Spot-clean smudges and fingerprints: with a small amount of diluted dish soap (one drop in a cup of water) on a microfiber cloth. Rinse the spot with a barely-damp clean cloth, then dry.

Door hardware is not part of the door finish but directly affects door performance and the surface around it.

• Wipe handles, knobs, and hinges with a dry or slightly damp cloth. Use a finish-matched metal cleaner for tarnish if needed, but keep the cleaner away from the door surface.
• Lubricate hinges annually with a dry PTFE lubricant or a light machine oil. Squeaky hinges create vibration stress on the door panel over time.
• Check door alignment every 6-12 months. A door that drags or binds at the frame is usually a hinge or settlement issue — do not sand or plane the door edge before checking hinge alignment.
• Tighten loose hinge screws immediately. A loose hinge causes the door to sag and drag, which scuffs the bottom edge and the frame.

Unlike solid wood, veneer cannot be deeply sanded and re-finished without risk of sanding through the layer. The protective coating — whether lacquer, oil, or UV-cured polyurethane — is what separates the wood from the environment. When that coating is damaged, moisture gets in. Care for the coating first; care for the wood follows.

• Daily / weekly: dry microfiber cloth. Always wipe with the wood grain — cross-grain wiping can catch in texture and create micro-scratches.
• Light soil / smudges: barely-damp microfiber cloth with plain water. Dry immediately. This handles 90% of cleaning needs.
• Stubborn grime or greasy marks: a few drops of pH-neutral wood cleaner (Murphy Oil Soap diluted to 1/4 strength, or a product labeled safe for lacquered wood) on a damp cloth. Wipe, then rinse with a clean damp cloth, then dry.
• Glass inserts (if present): clean glass with a glass cleaner sprayed onto the cloth — never directly onto the door. Wipe glass only; keep cleaner away from the veneer border.

Water is veneer's most dangerous enemy — not because of the water itself, but because of what happens when it gets under the coating and reaches the wood layer.

• Never wet-mop a floor right up to the door base without immediately drying the door bottom. Use a floor protector or door sweep.
• Never use a wet cloth on veneer. Barely damp only. The cloth should not leave any standing water on the surface at any point.
• If water is spilled on the door, blot immediately with a dry cloth. Do not rub — rubbing spreads the water and can lift the finish edge.

If your doors have an oiled finish (this is specified in your order), the oil needs periodic replenishment as it depletes from cleaning and normal use. A properly maintained oil finish actually improves with time — an unmaintained one will look dry, dull, and eventually gray.

• Re-oil frequency: every 12-24 months in normal use, or when the surface appears dry or dull when viewed in raking light.
• Product to use: the same oil specified in your door documentation (typically a hard wax oil or specific wood oil). Do not substitute with linseed oil, olive oil, or cooking oils — these turn rancid and stain.
• Application: apply a thin coat with a lint-free cloth, rub in with the grain, let sit 15-20 minutes, then buff off all excess. Wipe with the grain throughout. Let cure 24 hours before normal use.
• Patch repair: small scratches in oiled veneer can be spot-oiled. Clean the area, apply a tiny amount of oil, buff. This often makes scratches nearly invisible.

Because eco-veneer is non-porous, it does not absorb water or react to humidity the way wood does — a major practical advantage in kitchens, bathrooms, and homes with children. However, the film is mechanically bonded to the substrate, and that bond can be attacked by heat, harsh chemicals, or sharp impacts.

• Regular cleaning: dry or slightly damp microfiber cloth. Eco-veneer is the most forgiving finish to clean — most marks wipe off easily with plain water.
• Dried food, crayon, or marker: slightly dampen the cloth with a diluted mild soap solution (dish soap, 2-3 drops per cup of water). Wipe the mark, then follow with a clean damp cloth, then dry.
• Permanent marker or ink: a small amount of rubbing alcohol (isopropyl, 70%) on a cotton ball can remove ink. Use sparingly — blot the mark, do not rub. Test in an inconspicuous spot first. Do not use acetone.
• Greasy fingerprints: diluted dish soap on a damp cloth handles these easily. The non-porous surface releases oils without needing any solvent.
• Textured surface grooves: use a soft toothbrush or the corner of a microfiber cloth to dislodge grime from deep texture patterns. Always damp, never abrasive.

The most common and preventable eco-veneer failure is edge lifting caused by localized heat. Once an edge begins to lift, dust and moisture enter underneath, and the problem accelerates quickly.

If an edge begins to lift: do not pull it. Apply gentle pressure with a clean finger to push it back. If the bond has failed, use a thin bead of PVA wood glue applied with a toothpick under the edge, press firmly, and wipe away excess immediately. Let dry under light pressure (book, weight) for several hours.

Factory acrylic coatings are water-based and cure to a hard, cleanable film. They offer excellent color retention, flexibility across humidity cycles, and compatibility with standard mild cleaning agents. The finish is available in multiple sheen levels — matte, satin, and semi-gloss — and the care approach varies slightly by sheen (detailed below).

• Regular cleaning: dry microfiber cloth for dust. A barely-damp cloth handles most smudges on acrylic without any soap.
• Grime and fingerprints: a diluted solution of mild dish soap (3-4 drops per cup of warm water) on a soft cloth. Wipe, rinse with a clean barely-damp cloth, then dry.
• Scuffs from shoes, furniture, or belt buckles: light scuffs often wipe away with a damp cloth on semi-gloss acrylic. If the scuff is embedded on semi-gloss, try a Mr. Clean Magic Eraser (melamine foam) very gently. Do not use on matte or satin finishes — the abrasion creates visible sheen differences.
• Stickers or adhesive residue: apply a small amount of vegetable oil or baby oil to the adhesive, let sit 2 minutes, then wipe with a damp cloth and mild soap. Avoid petroleum-based adhesive removers.
• Crayons or wax: remove bulk first with a plastic scraper (never metal). Then apply a small amount of white toothpaste (non-gel) with a soft cloth, wipe gently, rinse with damp cloth, dry.

Acrylic touch-ups are more forgiving than solvent-based coatings because water-based paints feather and blend better at edges. Even so, spray-applied factory finishes will show brush marks on close inspection. Manage expectations accordingly.

• For small chips: clean the area with a damp cloth, dry, then apply matching acrylic paint with a fine artist's brush in multiple thin coats.
• For larger areas: full panel re-painting gives the best result. Lightly sand (220 grit), wipe dust, apply a compatible acrylic primer coat, then two finish coats.
• Sheen matching: always match the sheen level. A satin touch-up on a matte panel is visible even with a perfect color match.

Gloss surfaces require clean, lint-free microfiber and a careful sequence. The wrong technique polishes in scratches rather than removing them.

• Remove dust first: use a clean, dry microfiber cloth in straight, light passes. Never use a paper towel, tissue, or cotton cloth — these are coarse enough to micro-scratch gloss under light pressure.
• Damp-wipe: lightly dampen a separate clean microfiber cloth with plain distilled water (tap water leaves mineral spots on gloss). Use straight, consistent strokes — do not use circular motions, which leave visible swirl marks.
• Buff dry: immediately follow with a third dry microfiber cloth using the same straight-stroke technique. Do not let water air-dry on gloss — watermarks are almost impossible to remove once dried in.
• Fingerprints: a microfiber cloth with a tiny amount of diluted dish soap (1 drop per cup of distilled water) removes fingerprint oils cleanly. Follow with a damp rinse cloth, then dry immediately.
• Persistent smears: a small amount of diluted white vinegar (1 part vinegar, 4 parts distilled water) on a microfiber cloth removes haze and smears effectively on gloss lacquer. Rinse with a plain damp cloth and dry.

Frosted glass (acid-etched or sandblasted) has a textured, matte surface that scatters light. The texture traps residue more easily than clear glass and requires gentler cleaning.

• Routine cleaning: a barely-damp microfiber cloth with plain water removes most dust and light soil. Wipe gently — the texture holds dirt loosely and releases it without scrubbing.
• Smudges and fingerprints: diluted mild dish soap on a damp microfiber cloth. Rinse with a clean damp cloth, pat dry. Do not rub hard — aggressive rubbing drives residue deeper into the texture.
• Never use: abrasive cleaners, scouring pads, or anything that scratches — the frost texture is a surface treatment and cannot be restored once abraded.
• Streaks on frosted glass: are rare because the texture diffuses light, but if soap residue is visible after drying, wipe gently with a plain damp cloth to remove the residue.

Clear glass panels show every smudge, water spot, and streak immediately. The approach here prioritizes streak-free results.

• Best technique: spray glass cleaner (Windex or equivalent) onto a clean microfiber cloth — never directly onto the glass, as overspray will reach the joint. Wipe in straight overlapping strokes.
• Mineral spots and hard water deposits: a solution of 50% white vinegar and 50% distilled water on a microfiber cloth removes mineral deposits effectively. Apply, let sit 30-60 seconds, wipe, and dry.
• Dry immediately: use a second dry microfiber cloth or a lint-free chamois to buff dry before the cleaning solution air-dries and leaves streaks.

Mirror glass inserts have a reflective silver or aluminum backing that is protected by a paint layer on the rear face. The mirror surface itself is the front face and is cleaned like clear glass, but with additional caution about the edges.

• Clean the front face: same method as clear glass — glass cleaner applied to the cloth, straight strokes, buff dry.
• Never wet the edges or back: moisture reaching the mirror backing through the edge will cause black edge spots (mirror rot) — a permanent oxidation of the silver layer. Keep the edges dry.
• Never use ammonia-based cleaners on mirror: over time, ammonia attacks the silver backing through micro-pores in the edge seal. Use ammonia-free glass cleaner for mirror inserts.

Opaque black glass (also called lacquered glass or back-painted glass) is a clear glass panel with an opaque coating on the rear face. The front surface is smooth and glass-like; the back coating is more delicate.

• Front face cleaning: same as clear glass. Glass cleaner on cloth, straight strokes, dry immediately. The glossy black surface shows fingerprints prominently — wipe after each use in high-traffic locations.
• Never clean the back face: the opaque coating on the rear is not designed for cleaning or contact. It faces the door panel interior and should never be accessible. If the panel is ever removed, handle it by the edges only.
• Avoid ammonia on opaque black glass: ammonia-based cleaners can cause hazing or discoloration of the back coating if they work around the edge. Use ammonia-free glass cleaner.

Grease is the main kitchen challenge — it accumulates in a thin invisible film on door surfaces near ranges and can be mistaken for normal discoloration until it has built up significantly.

• Clean kitchen-adjacent doors monthly with a diluted dish soap solution rather than just water — dish soap is specifically formulated to cut grease.
• The back of a kitchen door (facing into the kitchen) accumulates far more grease than the hall-facing side. Do not neglect it.
• Do not install wood veneer doors directly adjacent to a range without a ventilation hood above the range. Grease-laden steam discolors and penetrates veneer finishes.

Doors in children's spaces deal with crayon, marker, stickers, scuffs from toys and furniture, and the occasional projectile impact.

• Eco-veneer doors are the recommended choice for children's rooms — they are the most damage-resistant and easiest to clean.
• Crayon and most markers come off eco-veneer and enamel with a slightly damp cloth and a small amount of dish soap. Attack while fresh — dried crayon is harder to remove.
• Sticker management: remove stickers as soon as possible. The longer the adhesive contacts the finish, the more residue it leaves. Use the oil method (Section 4.2) for stubborn residue.
• Scuffs at handle height are the most common wear point in children's rooms. Consider a handle that minimizes push-plate contact, and wipe this area weekly.

Low-risk environments, but a few specific concerns apply.

• Sunlight exposure: sustained direct sunlight fades all interior finishes over time. Wood veneer may lighten unevenly. Film-wrap adhesive can soften. Use window film or shading to limit direct UV exposure to doors.
• Candles and incense: soot from candles deposits a very fine black film on door surfaces, especially around air currents and door gaps. Regular dry-dusting removes this before it becomes difficult.
• HVAC vents: avoid mounting doors directly in the path of heating or cooling vents, which cause extreme localized humidity swings and temperature cycling.